Get In Touch

Professional air compressor supplier with 20 years of manufacturing experience.

Contacts
Location
2311, Commercial Building, Cultural And Sports Center, Shajing Street, Shenzhen ,Guangdong ,China

Blog Details

Screw Air Compressor for Brick Plants: 6 Specs That Save Power

One night of lost compressed air can stall a brick plant’s molding line and leave a tunnel kiln idle — while the electricity meter keeps running at the full 24-hour rate. In a brickworks, the screw air compressor for brick plants is usually the first machine to fail, because clay dust, kiln heat, and continuous duty punish ordinary units. Specify the wrong machine and you end up with a compressor that trips on high temperature, chokes on dust, and burns 10–15% more power than it should. This checklist shows the six specs that keep a brick plant’s compressed air stable and cheap.

Why a Brick Plant Punishes Ordinary Rotary Screw Compressors

A clay brick line is not a clean machine shop. Three conditions break standard rotary screw air compressors within months:

  • Clay dust. Green clay and fired-clay dust clog intake filters, coat coolers, and wear the air end. An undersized filter turns into a pressure restriction inside a week.
  • Kiln heat. Tunnel kilns and dryers push ambient air near the compressor room past 40°C. A machine rated only for 40°C ambient trips on high temperature on a summer afternoon.
  • 24/7 duty. Molding presses, palletizers, and pneumatic conveying run around the clock, so load and unload cycles never stop and the oil never cools down.

Every one of these conditions is a cost, not just an inconvenience. A high-temperature trip during a night shift can stop the whole line until a technician arrives.

Six Screw Air Compressor Specs for Brick Plants That Never Stop

When you compare quotations, make these six checks non-negotiable:

  1. Oversized inlet filtration. Demand a large air filter and a two-stage air intake that handles clay dust. A bigger filter surface means fewer pressure losses and longer service intervals.
  2. 52°C ambient rating. Choose a machine designed to run at 52°C ambient, not the 40°C industry standard. The larger cooler keeps the oil temperature inside a safe band even next to the kiln.
  3. Two-stage compression with a permanent-magnet VSD. A two-stage unit compresses in two steps, staying closer to isothermal compression and lifting efficiency 10–15%.
  4. Hard-piped air and oil lines. Hard pipework instead of flexible hoses removes the leak points that silently waste compressed air between shifts.
  5. A dryer and water separator upstream. Wet air sticks the valves in brick molding machines. Dry air keeps actuators clean and cycle times consistent.
  6. Remote monitoring with alarm history. A controller that logs pressure, temperature, and alarms lets you catch a failing filter or a rising oil temperature before it stops the night shift.

The Energy Math: Two-Stage Cuts the Kiln Power Bill

The biggest cost of a brick plant air system is not the purchase price. It is the electricity burned over 10 years. Specific power — kilowatts consumed per cubic meter of air per minute — decides that bill.

In a factory comparison of compressor data sheets, a 90 kW single-stage screw unit runs around 7.0 kW per m³/min, while a two-stage unit drops to 5.9 kW per m³/min. That is roughly 16% less electricity for the same air flow.

Run a 90 kW machine for 8,000 hours a year, and a 16% cut saves about 115,000 kWh. At 0.10 USD per kWh, that is more than 11,000 USD back in the first year alone — before you add the 20–50% savings that a permanent-magnet motor and variable-speed drive deliver on part-load demand.

This is why a two-stage screw air compressor is worth the higher upfront cost for a plant that never stops.

What Buyers Get Wrong

  • Myth: a bigger motor means more air. A 90 kW single-stage machine can deliver less usable air than a well-matched 75 kW two-stage unit. Match on flow (m³/min) and specific power, not motor size.
  • Mistake: buying on purchase price alone. Energy is 70% or more of the lifetime cost. A cheap compressor that burns 16% extra power can cost you more in 18 months than the price difference.
  • Mistake: skipping the dryer. In a dusty, warm plant, condensation reaches the molding machine valves. The repair bill and lost production are far higher than the cost of the dryer.

Get a Spec Sheet Before You Pay the Deposit

Before you commit to any supplier, ask for the specific power figure at your required flow and pressure, the ambient temperature rating, and the noise level measured 1 m from the cabinet. Then compare the numbers, not the brochures.

A correctly specified screw air compressor for brick plants pays for itself through fewer trips, less dust damage, and a lower power bill. Start by reviewing our rotary screw air compressor range and models, then contact us with your required flow, pressure, and shift hours for a like-for-like quotation.