Get In Touch

Professional air compressor supplier with 20 years of manufacturing experience.

Contacts
Location
2311, Commercial Building, Cultural And Sports Center, Shajing Street, Shenzhen ,Guangdong ,China

Blog Details

Screw Air Compressor Oil Carryover: What the 3–5 ppm Outlet Rating Really Means

3–5 ppm sounds tiny, but it decides whether your compressed air is clean enough for a spray booth or safe enough for food contact. Screw air compressor oil carryover is the residual oil that leaves the air–oil separator together with the compressed air stream. Spec the wrong limit and you get fisheye in paint, contamination in packaging, and a filtration bill that quietly erases your energy savings. Here is what the rating means and how to verify it before you pay.

What Screw Air Compressor Oil Carryover Actually Measures

Oil carryover is reported in ppm, which for compressed air is effectively milligrams of oil per cubic metre of air. A standard oil-injected rotary screw machine is normally designed so that its separator outlet keeps residual oil at 3–5 ppm. That figure describes only the oil mist that gets past the separator core. It is not the same as the oil quality that reaches your tool or product, because every downstream pipe, receiver, and filter changes the final number. It is also not a constant: carryover rises as the separator core loads up, as inlet air temperature climbs, and as the machine runs above its rated flow. If you are still matching a machine to your plant, start with the rotary screw air compressor guide.

How 3–5 ppm Maps to ISO 8573-1 Air Quality Classes

ISO 8573-1 groups oil into classes by residual concentration. Class 1 allows no more than 0.01 mg/m³, Class 2 allows 0.1 mg/m³, Class 3 allows 1 mg/m³, and Class 4 allows 5 mg/m³. A 3–5 ppm separator outlet therefore lands near Class 4. That is fine for general tools and blow-off duty, but paint, powder coating, electronics, food, and pharma lines usually need Class 1 or Class 2, which a separator alone will not reach.

  • Class 1: ≤ 0.01 mg/m³ — electronics, pharma, and cleanrooms
  • Class 2: ≤ 0.1 mg/m³ — paint and food-contact processes
  • Class 3: ≤ 1 mg/m³ — general instrumentation air
  • Class 4: ≤ 5 mg/m³ — tools and general factory air

Why Separator Design Matters as Much as the Number

The 3–5 ppm claim only holds if the separator vessel is sized for the machine’s real flow. A separator works by slowing the air enough for oil droplets to settle, so the vessel should keep gas velocity at roughly 0.8–1 m/s. Push a separator past that speed and carryover climbs even when the core is brand new. Oil load matters just as much: a direct-coupled single-stage airend may inject oil at around 0.7% of inlet volume, a belt-drive unit closer to 1.0%, and a gear-driven two-stage airend up to 10%, because the higher rotor speed and inter-stage heat need far more oil for sealing and cooling. A machine on the high end of that range needs a larger separator to hold the same 3–5 ppm outlet, so the same promise must be verified at full flow and rated pressure, not at an idle test point.

What Buyers Get Wrong

  • Assuming oil-injected means no oil in the air — 3–5 ppm is still oil, just a controlled amount.
  • Buying on brand name instead of asking for a tested outlet oil figure at full load.
  • Skipping the downstream coalescing filter and then blaming the compressor for paint defects.
  • Comparing ppm numbers from different machines without checking pressure, flow, and temperature test conditions.

Checklist Before You Accept a Quote

  • Request the outlet oil content at the separator, not a generic oil-injected label.
  • Confirm the test condition: rated pressure, full flow, and normal inlet temperature.
  • Map the figure to the ISO 8573-1 class your process actually requires.
  • Add a coalescing filter if you need below 1 ppm on an oil-injected machine.
  • Ask how the separator vessel is sized, especially for gear-driven two-stage units.

Checking screw air compressor oil carryover before you buy prevents a cheap quote from becoming an expensive filtration retrofit. Pin the supplier to a number, confirm the test condition, and match it to the ISO class your process really needs. If your process cannot tolerate oil, an oil-free screw compressor is the cleaner starting point, and we can help you compare the two before you commit.