Get In Touch

Professional air compressor supplier with 20 years of manufacturing experience.

Contacts
Location
2311, Commercial Building, Cultural And Sports Center, Shajing Street, Shenzhen ,Guangdong ,China

Blog Details

Screw Air Compressor Starting Current: 6x Inrush vs 1.2x Soft Start

When a 75 kW screw air compressor starts directly on line, its screw air compressor starting current can spike to 600–840 A for several seconds — six to seven times the roughly 120 A the motor pulls while running. That surge is not a curiosity. It is the reason breakers nuisance-trip, why the CNC spindle next door resets mid-cut, and why electrical panels get built one size too large. Fix the inrush and you stop paying for peak current you never actually use.

What Screw Air Compressor Starting Current Actually Is

A motor at rest is effectively a locked rotor. The instant the contactor closes, the winding pulls locked-rotor current to build its magnetic field and accelerate the airend up to speed. On a direct-on-line (DOL) fixed-speed screw compressor, that surge is typically 5–7 times the full-load running current. A 75 kW unit at 400 V / 50 Hz runs near 120 A, so for a few seconds after every start it can demand 600–840 A before the rotors spin up. That is why a nameplate lists a locked-rotor code letter next to the rated amps — the letter tells you exactly how many kVA the machine will pull in the first second.

What a 6x Inrush Spike Costs Your Plant

A start that lasts a few seconds still carries a long tail of cost and risk:

  • Voltage dip: a large inrush can sag the bus far enough that PLCs, drives, and CNC controllers fault or reset.
  • Nuisance trips: a panel sized for running current needs a D-curve breaker and oversized cable just to survive start-up, or it trips at the worst moment.
  • Winding heat: every high-current start heats the motor insulation; repeated starts quietly shorten its life.
  • Demand charges: utilities bill the highest peak you draw, and a 6x start spike lifts the peak you pay for all month.

How a PM VSD Cuts Inrush to 1.2–1.5x

A permanent-magnet variable-speed drive ramps the motor from 0 Hz, so the rotor never sees a locked-rotor condition. Starting current is held to about 1.2–1.5 times rated — for that same 75 kW machine, roughly 145–180 A instead of 600–840 A. The same ramp logic is what holds system pressure to ±0.01 MPa and keeps a PM motor above 95% efficiency across the range instead of sagging at low speed. See the full variable speed screw air compressor guide for how the drive behaves under partial load.

Starting Methods Compared

  • DOL (direct on line): cheapest wiring, 5–7x inrush, and hard mechanical shock to the airend every start.
  • Star-delta: cuts current to about one-third during ramp, but torque drops with it and the delta transition can still spike.
  • Soft starter: reduces inrush to roughly 2–3x, but it does not add partial-load energy savings.
  • VSD soft start: 1.2–1.5x inrush plus permanent energy savings whenever the machine runs below full flow.

If your plant already spends hours at partial load, the drive earns back its premium on electricity; the soft start is a free side benefit on top. The common objection is “my compressor only starts twice a day.” The answer is simple: if the panel and breaker were sized for a 6x spike, you already paid for capacity you use for only a few seconds each day — and every start still hammers the windings.

Buyer Checklist Before You Wire the Panel

  • Ask for the locked-rotor / starting current on the nameplate or data sheet — not just the rated kW.
  • Confirm the drive ramps from 0 Hz with current limiting rather than a timed star-delta transition.
  • Size the breaker to the drive’s real inrush so you do not over-buy cable and panel capacity.
  • On a retrofit, check the existing feeder: limiting inrush to 1.5x often lets you reuse the current supply.

Next Step

Starting current is one of the cheapest things to get right before you buy and one of the most expensive to ignore. Begin with the main rotary screw air compressor guide, then request a starting-current spec on the VSD range before you size any panel. Ready for a machine that will not spike your electrical room? Contact us with your kW, voltage, and how often the compressor starts.